Bark Texturing Die

These 5" (127mm) long bark texturing dies will quickly produce bark or vine texturing on 1/2" (13mm) through 2" (49mm) diameter stock. Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Beveling Power Hammer Die

These 5" (127mm) sloped surface dies will quickly produce bevelled edges on any size stock. Great for hinges, rails, flinch plates. . . Two different slopes, 1 : 5 and 1 : 3.33, for low sharp or high steep bevels. The Beveling set comes with our standard radius side die for the bottom. You may order the top Beveling die alone here. Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Singular Bit

Pack of 3 Bits

Bit Holder

Universal Concave Bottom Bowl Power Hammer Die

The universal bottom bowl die (usually bought with the top bowl die) is the result of 15 years of searching for better ways to forge bowls. Used to cold forge annealed copper brass and steel plate. Action is similar to raising and can produce a variety of curves and sizes. Not of a standard length and width.

3" Sphere Top Bowl Power Hammer Die

The 3" top bowl die (usually bought with bottom concave die) is the result of 15 years of searching for better ways to forge bowls. Used to cold forge annealed copper brass and steel plate. Action is similar to raising and can produce a variety of curves and sizes. Not of a standard length and width.

6" Sphere Top Bowl Power Hammer Die

The 6" top bowl die (usually bought with bottom concave die) is the result of 15 years of searching for better ways to forge bowls. Used to cold forge annealed copper brass and steel plate. Action is similar to raising and can produce a variety of curves and sizes. Not of a standard length and width.

10" Sphere Top Bowl Power Hammer Die

These 10" top bowl die (usually bought with a bottom concave die) are the result of 15 years of searching for better ways to forge bowls. Used to cold forge annealed copper brass and steel plate. Action is similar to raising and can produce a variety of curves and sizes. Not of a standard length and width.

Left Combination Power Hammer Die

Dimensions are 5"(127mm) long by 1.75" (44.45mm) wide. Standard length and width. Usually sold together with right combination power hammer die as BIG BLU Combo Dies.

Right Combination Power Hammer Die

Dimensions are 5"(127mm) long by 1.75" (44.45mm) wide. Standard length and width. Usually sold together with left combination power hammer die as BIG BLU Combo Dies.

Small Crown Die

Great for detail work in small stock or fine details in large stock. Used to great advantage for power hammer detailing. These act like the pein of your hand hammer, you are able to control the movement of metal in any direction. The critical radii on these dies are CNC machined and then carefully hand dressed by professionals. 2.5" (63.5mm) long.

Standard Crown Die

Crown Dies are used to great advantage for free hand sculptural work. These act like the pein of your hand hammer, you are able to control the movement of metal in any direction. The crown dies and the combo dies are a must have for the artist blacksmith. The critical radii on these dies are CNC machined and then carefully hand dressed by professionals that use these dies daily. 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Large Crown Power Hammer Die

Aggressive Drawing Die

Very aggressive for isolation, fast drawing, sculptural work with heavy forged texture and features. These are similar to the narrow side of the combination dies but will fit much larger work. The shape of these dies are CNC machined and then carefully hand dressed by professionals. 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Large Drawing Power Hammer Die

Standard Flat Die

Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Untempered Power Hammer Standard Flat Die

Large Flat Die

The dimensions are 2.5" wide, 5" long, 3" tall.

Untempered Power Hammer Large Flat Die

Bottom Super Flat Power Hammer Die

Untempered Bottom Super Flat Power Hammer Die

Untempered Bottom Super Flat Power Hammer Die, usually bought together with Untempered Top Super Flat Power Hammer Die.

Top Super Flat Power Hammer Die

Untempered Top Super Flat Power Hammer Die

Untempered Top Super Flat Power Hammer Die, usually bought together with Untempered Bottom Super Flat Power Hammer Die.

Aggressive Fuller Texturing Die

These 5" (127mm) long texturing dies will quickly fuller or texture up to 5" (127mm) wide stock. Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Left Knife Making Power Hammer Die

This is a single left power hammer die from a knife maker die set. These subtle and elegant dies are specifically designed for bladesmithing by leaders in the knifemaking community. These dies are lightly crowned in all direction, facilitating the crisp multidirectional tapering required to form a blade. Three sides have a ¼” radius and one side has a 1/8” radius allowing you to form shoulders. The smith can even offset the dies to set the tang of the knife to one side with an inner fillet. All done under the hammer. The shape of these dies are CNC machined and then carefully hand dressed by professionals. 5" (127mm) long. 1-3/4” (44.45mm) wide. Standard length and width. You can check these dies out in action on our YouTube channel.

Right Knife Making Power Hammer Die

This is a single right power hammer die from a knife maker die set. These subtle and elegant dies are specifically designed for bladesmithing by leaders in the knifemaking community. These dies are lightly crowned in all direction, facilitating the crisp multidirectional tapering required to form a blade. Three sides have a ¼” radius and one side has a 1/8” radius allowing you to form shoulders. The smith can even offset the dies to set the tang of the knife to one side with an inner fillet. All done under the hammer. The shape of these dies are CNC machined and then carefully hand dressed by professionals. 5" (127mm) long. 1-3/4” (44.45mm) wide. Standard length and width. You can check these dies out in action on our YouTube channel.

Single Peening Die

These 5" (127mm) semispherical texturing dies will quickly produce hammered texturing on any size stock. Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Multi Peening Die

Dimensions are 5" (127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Platform Dies

Single Platform Die

Radius Side Die

Dimensions are 5"(127mm) long by 1.75" (44.45mm) wide. Standard length and width.

Full Radius Fullering Die

An old standard used for fullering, heavy drawing and texturing, sculptural work with heavy forged texture and features. The shape of these dies are CNC machined and then carefully hand dressed by professionals. 5" (127mm) long. 1.25" (32mm) Primary Radius

Reverse Radius Power Hammer Die

These 5" (127mm) long mated curved surface dies will quickly produce cupped rail or other curved shapes. By rotating the work on the long axis you can form larger curved widths. The shape of these dies are CNC machined and then carefully hand dressed by professionals.